The temperature of the surface must be at least 3☌ above the dew point. Recommended film thickness: 40 pm dry, (100 pm wet). During application the surface must be clean and dry.Īpply undiluted in at least two coats using a nylon roller or a polyester brush.įor the best results use EpoxyShield Sealer 5220 as first coat. Remove poorly-adhering old coatings with wire brush and sandpaper. Roughen still-intact floor coatings to ensure good adherence. Roughen well-sealed and smooth concrete and treat with Epoxyshield Sealer 5220. Repair all holes and cracks with EpoxyShield concrete repair products.Īlways pre-treat absorbent, porous surfaces with EpoxyShield Sealer 5220. Armor Gray Satin 1-Part Epoxy Concrete Floor Interior/Exterior Paint: 5 Gal. Remove laitance, loose and damaged concrete by sandblasting or keying with RUST-OLEUM Surfa-Etch 108. Rust-Oleum: Rust-Oleum: Rust-Oleum EpoxyShield: ARMORPOXY: Name: 5 Gal. Allow new concrete to set for at least 30 days. Remove oil, grease and all other contaminants with EpoxyShield Cleaner/Degreaser 2901. Do not apply to smooth and completely sealed concrete or concrete containing a curing compound. Only apply to completely clean and dry concrete floors. Good resistance to diesel, motor oil, coolant fluid, various household chemicals and most types of tyre. It is not recommended to apply on smooth/dense concrete or concrete containing a curing compound, which will prevent a good adhesion.Quick-drying single pack water-based floor coating (epoxy-modified acrylic) for light to medium duty (normal foot traffic/limited vehicular traffic). Immediately continue to coat the next section (note: fresh paint can be applied over the loose chips that lay outside the previously painted area). This will not affect the performance of the coating). Sprinkle the decorative paint chips onto the wet film (note: this step may be skipped if chips are not desired. Maintain a wet edge to prevent lap marks and gloss differences. Apply in sections of 1,5 x 1,5 m so that Epoxyshield Decorative Chips can easily be scattered on the freshly coated surface. Application and ThinningĪfter the full 60 minutes use a paint roller (20 cm) to apply an even coat to the surface. Do not mix Paint Chips with Epoxyshield Garage floor coating. This time decreases at higher temperatures. The product must be used within 1 to 2 hours of initial mixing. Do not leave container in direct sunlight. Allow mixed product to stand (see table) before rolling the coating on to the surface. ![]() Pour the contents of A into B and stir thoroughly for at least 3 minutes. Remove all water and allow to dry completely. Rinse thoroughly with fresh water afterwards. Remove oil and grease using a scrubbing brush and ND14 cleaner degreaser. If the floor is previously painted, remove any loose paint by sanding and scraping. They give a decorative finish and will also mask dirt. The chips adhere permanently on the floor when they are sprinkled in the wet coating. ![]() The Epoxyshield Decorative Chips are specially designed for use in combination with Epoxyshield Garage Floor Coating. Detailed instructions and a free Instructional DVD.Resists oil, petrol, anti freeze, salt and hot tyre pick up.It can also be applied on sound previously painted floors. Everyday Low Price 19.99 11 Mail-In Rebate Good Through 9/17/23 2.20 Final Price 17.79 17 79 each You Save 2.20 with Mail-In Rebate More Information Recommended for repairing minor holes and cracks in residential asphalt driveways. Epoxyshield Garage Floor Coating can be applied on concrete floors, which are completely clean and dry. Rust-Oleum® EPOXYSHIELD® Blacktop Patch & Crack Filler - 1 gal.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |